<fc #990000>Discontinued - Information for old sensors only!</fc>
<fc #000080> Sensor for measure soil temperature and humidity V2.0.0</fc>

Name: Sensor for measure soil temperature and humidity
Type: Sensor Board
Version: 1.0.0
Author: Dubravko Penezic
Copyright: Creative Commons BY-NC-SA v 3.0
Implemented function:

• Measure soil temperature in 3 points (20cm and 10cm deep and on soil level) with DS18B20
• 4 capacitive area (2 between 20cm and 10 cm deep, and 2 between 10cm deep and soil level)
• LED signaling (blue, green, red 0805 LED)
• 2×5 connector
• 2 3mm mounting holes
• Clear foil surface protection and dielectric grass pin temperature sensor protection
• Modular deep (PCB can be shorten to 10cm deep)
• Compatibile with Arduino 1-Wire and CapSense library (10M resistor and 220pF parallel condensator)

Revision to Schematic:
Add 4K7 pullup resistor to 1-wire line

Used library Dp1WBasic library, Dp1WDS18xxxTermo library and Capacitive Sensing .

DpSoilCapTempSensor_V_1_0.ino

/*
Author: Dubravko Penezic
 
Version: 1.0, 2013
 
This code is example how to use Sensor for measure soil temperature and humidity.
 
Source code is provided as is, without any warranty.
 
Distributetd under CC BY v 3.0
 
*/
 
// include 1Wire library
#include <Dp1WBasic.h>
#include <Dp1WDS18xxxTermo.h>
 
// Data wire is plugged into port 5 on the Arduino
#define ONE_WIRE_BUS 5
 
// Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs)
Dp1WBasic oneWire(ONE_WIRE_BUS);
 
// Pass our oneWire reference to Dallas Temperature. 
Dp1WDS18xxxTermo tSen(&oneWire);
 
// arrays to hold device address
SensorInfo tempSensors[16];
 
//include CapSense library
#include <CapSense.h>
 
CapSense   cs_7_9 = CapSense(7,9);        // 10M resistor between pins 7 & 9, pin 9 is sensor pin 
CapSense   cs_7_10 = CapSense(7,10);        // 10M resistor between pins 7 & 10, pin 10 is sensor pin
CapSense   cs_7_11 = CapSense(7,11);        // 10M resistor between pins 7 & 11, pin 11 is sensor pin
CapSense   cs_7_12 = CapSense(7,12);        // 10M resistor between pins 7 & 12, pin 12 is sensor pin
 
// set LED pin
byte led1 = 6;
byte led2 = 8;
byte led3 = 13;
 
void setup(void) {
  //   cs_7_9.set_CS_AutocaL_Millis(0xFFFFFFFF);     // turn off autocalibrate on channel 1 - just as an example
 
  Serial.begin(9600);
  Serial.println("DpSoilCapTempSensor V 1.0");
  pinMode(led1, OUTPUT);
  pinMode(led2, OUTPUT);
  pinMode(led3, OUTPUT);
  digitalWrite(led1, HIGH);
  digitalWrite(led2, HIGH);
  digitalWrite(led3, HIGH);
  delay(10000);
}
 
void loop(void) {
 
  byte broj = tSen.readTemperature(tempSensors, 16, NORMAL_SEARCH);
 
  if(broj == 0 ) { 
    Serial.print("\n\nNo 1-Wire Temperature Sensor Found on Digital Pin ");
    Serial.println(ONE_WIRE_BUS);
  } else {
    for(byte i = 0; i < broj; i++) {
      Serial.print("\n\nTemperature sensor ");
      Serial.print(i);
      Serial.println(".");
 
      Serial.print("ROM Address: \t\t");
      for(byte j=0; j<8;j++) {
        if (tempSensors[i].dAddr[j] < 16) Serial.print("0");
        Serial.print(tempSensors[i].dAddr[j], HEX);
      }
 
      Serial.print("\nSensor type: \t\t");
      switch (tempSensors[i].dAddr[0]) {
        case DS18B20MODEL:
	  Serial.println("DS18B20");
  	  break;
        case DS1822MODEL:
	  Serial.println("DS1822");
	  break;
        case DS18S20MODEL:
	  Serial.println("DS18S20/DS1820");
	  break;
      }
 
      Serial.print("Actual temperature \t");
      Serial.print(tempSensors[i].dTemperature);
      Serial.print(" C (");
      Serial.print(getResolution(tempSensors[i].dAddr,tempSensors[i].dTempReso),DEC);
      Serial.println(" bit)");
 
      Serial.print("Alarm Low Temperature \t");
      Serial.print(tempSensors[i].dMinAlarm,2);
      Serial.println(" C");
 
      Serial.print("Alarm High Temperature \t");
      Serial.print(tempSensors[i].dMaxAlarm,2);
      Serial.println(" C");
 
      if(i==0) {     
        if(tempSensors[i].dTemperature>28) {
          digitalWrite(led1, HIGH);
        } else {
          digitalWrite(led1, LOW);
        }
      }
      if(i==1) {     
        if(tempSensors[i].dTemperature>28) {
          digitalWrite(led2, HIGH);
        } else {
          digitalWrite(led2, LOW);
        }
      }
      if(i==2) {     
        if(tempSensors[i].dTemperature>28) {
          digitalWrite(led3, HIGH);
        } else {
          digitalWrite(led3, LOW);
        }
      }
 
    }
  }
 
  for(byte j = 0; j <25; j++) {
     long start = millis();
     long total1 =  cs_7_9.capSense(30);
     long total2 =  cs_7_10.capSense(30);
     long total3 =  cs_7_11.capSense(30);
     long total4 =  cs_7_12.capSense(30);
 
     Serial.print(millis() - start);        // check on performance in milliseconds
     Serial.print("\t");                    // tab character for debug windown spacing
 
     Serial.print(total1);                  // print sensor output 1
     Serial.print("\t");
     Serial.print(total2);                  // print sensor output 2
     Serial.print("\t");
     Serial.print(total3);                // print sensor output 3
     Serial.print("\t");
     Serial.println(total4);                // print sensor output 3mit data to serial por
 
     delay(20);
  }
}
 
byte getResolution(uint8_t* deviceAddress, uint8_t conf) {
 
  if (deviceAddress[0] == DS18S20MODEL) return 9; // this model has a fixed resolution
 
  switch (conf) {
    case TEMP_12_BIT:
      return 12;
 
    case TEMP_11_BIT:
      return 11;
 
    case TEMP_10_BIT:
      return 10;
 
    case TEMP_9_BIT:
      return 9;
 
  }
 
  return 0;
}